The position of a magnetic float / piston is detected by means of Hall sensors and converted into an analog signal.
- Analog output (4-20 mA and 0-10 V)
With the help of Hall sensors, the position of magnetic floats / pistons is detected and output as an analog signal.
Transmitter with analog output signal + alarm contact
Analog output (4-20 mA or 0-10 V)
1 switching point (magnetic programming)
Status LED
Stainless steel case
With the help of Hall sensors, the position of magnetic floats / pistons is detected and output as an analog signal.
- Transmitter with analog output signal + alarm contact + display
- Backlit graphic display (LED)
- Analog output (4-20 mA)
- 2 switching points
- Programmable hysteresis
- Bright indicator LED
- Easy programming
The MFE multifunction electronic converts the original impulses of an oval wheel meter into a quantity or flow signal.
- For oval wheel meters of the OR, OR Plus, OF series
- EX version according to ATEX
- Battery supply or power supply
- Current output and / or pulse output
Display and calculation of measured values on site
- Output of calculated measured value (e.g. volume flow) as display and analog signal
- Configurable relay alarm outputs (e.g. falling / rising edge)
- Simple and quick installation directly on the wall or channel
Volume flow and medium temperature at a glance!
- Two-line display module
- Direct output of standard volume flow VN and medium temperature TM
- Remote display for optimal readability
- No additional power supply required
- Plug and play
Limit contact for flowmeter M335, M350
- Magnet built into the float
- Can be set to any value on the corresponding scale
Measured value sensor for flow meter M335, M350
- Electronics with microprocessor and sensors
- 4-20 mA output signal
Smallest lamp for sight glasses in the non-Ex area
- Only one size for all sight glass sizes
- Easy assembly using a tilt hinge
- Excellent, glare-free illumination thanks to halogen light
- Change of light bulbs without removing the light once it has been installed
- Suitable for use "view and light through a fitting"
Ex amplifiers with relay output for flow sensors STS / ST
- Ex II (1) G [Ex ia Ga] IIC
- Ex II (1) D [Ex ia Da] IIIC
- AC 230 V • AC 115 V • DC 24 V
- Relay output
- Cable break and short circuit monitoring
- Turn off delay
Analog EX amplifier device DC
- Ex II (1) G [Ex ia Ga] IIC
- Ex II (1) D [Ex ia Da] IIIC
- DC 24 V
- Analog output
- Cable break and short circuit monitoring
Reader for flow monitors
- Temperature monitoring
- Switch-off delay
- Relay switching output
- LED display
Reader for flow monitors
- Clamping rail assembly
- Analog output 4 ... 20 mA
- Relay switching output 17.5 mm modular housing
- 24 VDC DC voltage
Reader for flow monitors
- Clamping rail assembly
- Particularly convenient operation
- Integrated system error message
- Wide voltage range
- LED adjustment display
- Narrow design (23 mm)
The switch contact is intended for use with mechanical flow meters and serves to electrically monitor flow limits.
- Normally open or Change over
- Bi-stable switching behavior within the specified measuring range
- Sealed housing IP 65 or IP67 (depending on connection)
Reed contact for use with large mechanical flow meters
- Normally open or Change over
- Bi-stable switching behavior within the specified measuring range
- Sealed housing IP 65 or IP67 (depending on connection)
EX-Switching contact for small flowmeters
- EX version according to ATEX
- For use in zones 1, 2, 21 and 22
Connector
- Cable socket welded to cable
- Self-locking screw cap
- Degree of protection IP 67
Connector
- Cable socket can be assembled
- Large variety of cables
- Degree of protection IP 67
- Self-locking screw connection